1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button. 2. Press and hold the Instrument Cluster Set/Reset button for 10 seconds. 3. The upper display in the Instrument Cluster will be illuminated with a Service Item. The lower display in the Instrument Cluster will indicate the remaining time or

BMW X3 Owners Manual / Controls / Displays / Check Control / Indicator/warning lights. General information The indicator and warning lights in the instrument cluster can light up in a variety of combinations and colors. Several of the lights are checked for proper functioning and light up temporarily when the engine is started or the ignition

just performed a service on your G05 and don't know how to reset the service light? in this video I will demonstrate how to do so. ensure the engine is off a

How to Reset oil indicator after oil change in 2020 BMW X3M-CHere's a free copy of my book in pdf down load from my drop box! How to Reset oil indicator after oil change in 2020 BMW X3M-CHere 452 posts · Joined 2015. #3 · Apr 21, 2016. You just insert key, press start button but dont start the car. Hold down the reset button on the dash till a triangle appears, then let go. Now each press of the button will show a new service, once you find the brake fluid one press and hold again until RESET? appears. During the next reset, you’ll have to reset the brakes to 25,000 miles for the front and 31,000 for the rear. The values may vary by BMW model. Method Two To Reset Bmw Brake Light. Insert the key in the ignition and turn it on without starting the engine. Press and hold the BC button until time and mileage appear in the middle of the Traced problem by unplugging the sensor cable from the car wiring and placing a shorting wire in place of the sensor. If the reset now changes to 'possible' it's either a faulty sensor or dirty contact in the plug, both will make the car think you have not replaced the sensor and disable the reset. 10-09-2015, 08:00 PM #3.
I think BMW started this in the early 90's with their wacky 20-pin underhood connector for service interval resets! They could at least give us a way to acknowledge the message once and then just put a discrete wrench light reminder in the cluster, but NO they want their $$$$.
Coupled with the free version of the bimmerlink app, I was able to reset the dash service warning. Current - Second 2023 XM (first one was taken back by BMW) and 2023 X7 40i Past - 2009 X5 35d, 2011 MB E350, 2011 740i, 2015 X5 35d, 2018 M550i, 2019 X5 40i, 2021 M5C
\n \n\n\n reset bmw x3 service light

2004-2010. With the key in the OFF position, press and hold the TRIP or S/R button (located at the left side of the instrument cluster) and turn the ignition to the ACC position. Continue to hold the TRIP or S/R button until “Reset” is displayed in the message center. Release the TRIP or S/R button, then press and hold it again for 5

Step 1 is to turn off the ignition. Step 2: Turn the key to position 1 and press and hold the trip odometer button. Step 3: Press and hold the button for about five seconds until the display reads “Oil Service” or “Inspection” with “Reset” or “Re,” and then release. Step 4: Press and hold the button for an additional five seconds.
.
  • jf5714g2h2.pages.dev/361
  • jf5714g2h2.pages.dev/278
  • jf5714g2h2.pages.dev/348
  • jf5714g2h2.pages.dev/350
  • jf5714g2h2.pages.dev/339
  • jf5714g2h2.pages.dev/254
  • jf5714g2h2.pages.dev/421
  • jf5714g2h2.pages.dev/291

    • reset bmw x3 service light